Gebruikersnaam: Wachtwoord:
 

Auteur Topic: Fe501 rally build  (gelezen 16047 keer)

Offline member

  • Member
  • *
  • Berichten: 126
Re: Fe501 rally build
« Reactie #45 Gepost op: 08-04-2021, 22:04 »
I've not particular liked the looks of the cable-tied wires, around the GPS:




..and seeing as I got me a 3D printer..











The clip rings fit into place with a satisfying snap:







Modeling this:

into:



Looks much cleaner, I think



Still have to make some plan with that phone ram mount.. not sure yet





Offline member

  • *****
  • Berichten: 7958
Re: Fe501 rally build
« Reactie #46 Gepost op: 08-04-2021, 22:18 »
Nice

Offline member

  • *****
  • Berichten: 226
Re: Fe501 rally build
« Reactie #47 Gepost op: 08-04-2021, 22:30 »
now shorten the m8 bolts and then it is completely finished

Offline member

  • *****
  • Berichten: 7958
Re: Fe501 rally build
« Reactie #48 Gepost op: 08-04-2021, 22:42 »
Is geen M8
Standard dus in inches tis RAM

Offline member

  • *****
  • Berichten: 1020
Re: Fe501 rally build
« Reactie #49 Gepost op: 09-04-2021, 08:33 »
Voor de veiligheid zou ik die ram mount helemaal omdraaien. Nu is hij met de uitstekende bouten en moeren op de rijder gericht :-)
Husky 701, EXC-f 450 en Vertigo Fajardo 250
www.rollingmavericks.com

Offline member

  • *****
  • Berichten: 1532
Re: Fe501 rally build
« Reactie #50 Gepost op: 09-04-2021, 08:43 »
Ik denk dat de positionering van je mount wel het minste is waar je zorgen over hoeft te maken als je crached. En de mount beweegt gelukkig goed mee als je druk op uitoefend, het is geen vast object zoals een (scherpe) ruit voor je.
2021 690 Enduro R  -  Gamo Grizzly 1250 Whisper IGT 5.5

Offline member

  • Member
  • *
  • Berichten: 126
Re: Fe501 rally build
« Reactie #51 Gepost op: 09-04-2021, 09:01 »
Voor de veiligheid zou ik die ram mount helemaal omdraaien. Nu is hij met de uitstekende bouten en moeren op de rijder gericht :-)
Dat is idd mijn plan

Sent from my IN2013 using Tapatalk


Offline member

  • Member
  • *
  • Berichten: 126
Re: Fe501 rally build
« Reactie #52 Gepost op: 17-04-2021, 11:38 »

I've been in 2 minds about the stock handguards.
On the one hand, I really like their look and the handguard-mounted mirrors also flow nicely along the same lines:




On the other, I hate how the clutch and brake lines forces you to compromise with either the tilt of the guards or your controls. I can never get both to be exactly how I want them.




So that always leads me to aftermarket which is:
1) expensive
2) the Cycra's are a bit dated in look IMO



In ZA, its still OK to just tilt the guards down, but in EU, you need the protection from the elements. If only I could extend the exiting guards somehow   ::)

Post Merge: 17-04-2021, 11:39

Been experimenting with photogrammetry, better known as photo to mesh


Check, I scanned the existing handguard, by taking lots of photos and using Meshroom to create a mesh.


I will be printing the addon piece today.. holding thumbs

Offline member

  • *****
  • Berichten: 7958
Re: Fe501 rally build
« Reactie #53 Gepost op: 17-04-2021, 12:03 »
Heb de klemmen op het stuur.
Tot nu toe blijven ze heel en bevallen me.
Tis wel goedkope shit van Ali.


Post Merge: 17-04-2021, 12:04

Offline member

  • Kom op mensen, wordt ook
  • Donateur
  • *****
  • Berichten: 2318
Re: Fe501 rally build
« Reactie #54 Gepost op: 17-04-2021, 14:07 »
Been experimenting with photogrammetry, better known as photo to mesh


Check, I scanned the existing handguard, by taking lots of photos and using Meshroom to create a mesh.


I will be printing the addon piece today.. holding thumbs

Nice, looking forward to the result

Offline member

  • Member
  • *
  • Berichten: 126
Re: Fe501 rally build
« Reactie #55 Gepost op: 17-04-2021, 15:23 »
Unfortunately my support piece collapsed during print, so its not perfect yet:



Also still printing at 150%, so not best quality but OK for prototyping


Part is designed to fit inside the slots of the handguard:





Area circled in red was not fully printed due to support collapse


Post Merge: 17-04-2021, 15:28
Version 2 will have this part included.
It will be used to bolt everything together



Offline member

  • Member
  • *
  • Berichten: 126
Re: Fe501 rally build
« Reactie #56 Gepost op: 18-04-2021, 19:36 »
Got the left side done!


I must say, I'm happy with the result  ;D

There's a little 'H' in that Husqvarna emblem. Maybe I will also paint that yellow  8)



Post Merge: 18-04-2021, 19:37

It clearly offers better wind protection:


Post Merge: 18-04-2021, 19:38

and the foldable mirror, fits in nicely behind the wind shield:



Post Merge: 18-04-2021, 19:41

My garage need a cleaning, pardon the mess  ::)



Mirror folded inwards



One down, 1 more to go

Offline member

  • Member
  • *
  • Berichten: 69
Re: Fe501 rally build
« Reactie #57 Gepost op: 18-04-2021, 20:20 »
Well done.


Wow, nice build thread. Pleases the eye  8)
Husqvarna 701 Enduro LR

Offline member

  • Member
  • *
  • Berichten: 126
Re: Fe501 rally build
« Reactie #58 Gepost op: 18-04-2021, 20:47 »
Thank you

Sent from my IN2013 using Tapatalk


Offline member

  • Member
  • *
  • Berichten: 126
Re: Fe501 rally build
« Reactie #59 Gepost op: 24-04-2021, 18:47 »
Both handguards mounted  :D


Those USB cables can sometimes annoy me a bit, specifically when not plugged into something as they tend to rattle and flap around.

So I decided to solve that:



Plugging the cable into its housing, will at least also protect it from the rain
USB for the phone, which is used as a speedo mostly:


And the mini USB for the GPS: